Skip navigation

Energy Savings Agreement

Give us a call today: 940-382-8554

"Universal Savings Agreement"

Program includes the following benefits:

  • 15% Discount on all service repairs (all service parts & labor.)
  • Never pay an overtime fee (no matter what time of the day or night it is.)
  • Priority customer status (immediately moved ahead of non–customers.)
  • Increased capacity of existing system (restores equipment to as close to factory fresh specifications as possible.)
  • Improved comfort (a clean indoor coil on an air conditioning system tends to remove more moisture.)
  • Longer equipment life (well–maintained equipment lasts longer.)
  • Reduce equipment run time (when your system isn’t running – it’s saving you money.)
  • Transferrable to another location (or to the new owner.)
  • Fewer repairs (equipment that is regularly maintained normally have less costly repairs.)
  • Safer system (equipment that is clean and well–maintained tends to be safer to operate.)
  • Call for Commercial estimate for maintenance (Schedule appointment for free Commercial maintenance estimate)

"Exclusive Precision Tune-up"

Our exclusive precision tune-up is so much more than the typical "check and clean":

Heating Precision Tune-up

  • Cycle the complete system (air conditioning and heating, as well as fan operation).
  • Clean and level the thermostat - calibrate, adjust, and record heat anticipator setting.
  • Replace up to one standard 1" throwaway filter, or clean one permanent filter per system.
  • Remove & clean the indoor blower assembly which includes the blower wheel on the indoor unit.
  • Remove and clean the indoor blower motor on the indoor unit.
  • Lubricate all moving parts on indoor unit.
  • Test and record all voltages on indoor blower motor.
  • Test and record all amperages on indoor blower motor.
  • Test and examine all controls on indoor unit.
  • Tighten or adjust all belts and pulleys within indoor unit.
  • Test and record voltages on electric heat strips.
  • Test and record amperages on electric heat strips.
  • Clean and adjust burner assembly.
  • Test and clean ignition assembly.
  • Clean heat exchanger, and examine for possible cracks.
  • Test and record gas pressures at indoor furnace.
  • Leak test for gas leaks at furnace gas piping connections.
  • Monitor flue draft on gas furnace.
  • Examine and tighten all electrical connections within indoor unit.
  • Clean and apply protective coating to indoor cabinet of indoor unit.
  • Examine duct condition (if accessible).
  • Test and record indoor air temperature.
  • Test and record indoor temperature rise in heating mode.
  • Remove any trash or debris from indoor unit.
  • Replace any missing screws on indoor unit.
  • Examine and clean indoor evaporator coil (if accessible) if the unit is a heat pump system.
  • Clean and treat condensate drain line from indoor coil to main drain line (only to wall or floor) - if unit is a heat pump system.
  • Clean and treat condensate pump (if part of the cooling drain system) if the unit is a heat pump.
  • Test and record refrigerant pressures (low and high side) if the unit is a heat pump system.
  • Clean the outdoor condenser coil on outdoor unit if the unit is a heat pump system.
  • Remove any trash or debris from the outdoor unit if the unit is a heat pump system.
  • Clean and apply protective coating to cabinet of the outdoor unit ifit is a heat pump system.
  • Examine and tighten all electrical connections on the outdoor unit if it is a heat pump system.
  • Examine and test all outdoor controls on outdoor unit if it is a heat pump system.
  • Replace any missing screws on indoor and outdoor units.

Cooling Precision Tune-up

  • Cycle the system (Air Conditioning as well as fan operation).
  • Lubricate all moving parts on indoor unit.
  • Test and record all voltages on indoor blower motor.
  • Test and record all amperages on indoor blower motor.
  • Test and examine all controls on indoor unit
  • Tighten or adjust all belts pulleys within indoor unit.
  • Examine and tighten all electrical connections within indoor unit.
  • Examine indoor evaporator Coil (If accessible).
  • Clean condensate drains line from indoor coil to main drain line (only to wall or floor).
  • Examine duct conditions (if accessible).
  • Test and record indoor air temperature.
  • Test and record temperature drop in cooling mode.
  • Test and record refrigerant pressures (low and high side).
  • Monitor refrigerant charge in refrigerant system.
  • Test and record superheat on refrigerant system.
  • Test and record sub-cooling on refrigerant system.
  • Clean outdoor condenser coil unit.
  • Remove any trash or debris from outdoor unit.
  • Examine and tighten all electrical connections on outdoor unit.
  • Examine and test all controls on outdoor unit.
  • Test safety controls on outdoor unit.
  • Test and record all voltage on outdoor unit (fan motor and compressor).
  • Test and record all amperages on outdoor unit (fan motor and compressor).
  • Lubricate all moving parts on outdoor unit.
  • Clean return air grilles

Do We Serve Your Neighborhood?